Engineering Notes

Motor Starter vs Contactor: A Schneider TeSys Selection Guide From Someone Who Got It Wrong

Posted 2026-11-03 by Kwame Boateng

Real talk: there is no single right answer to contactor versus motor starter. The right choice depends on four things — the load, how you control it, how often it switches, and whether the panel needs short-circuit protection and isolation in one tested combination. Nobody who skips those four questions gets it right by luck.

I have been handling contactor and motor-control orders for industrial buyers and panel shops for eight years. I have personally made, and written down, 11 significant mistakes on those orders — roughly $6,400 in budget that went nowhere. The coil-voltage mix-up is the one I am least proud of, because it was avoidable in about 30 seconds of checking. Now I keep the checklist that stops other people from repeating it.

The four situations I actually see

Almost every contactor-versus-starter question that lands in my inbox falls into one of these buckets:

  1. A single motor on direct-on-line (DOL) start, already protected upstream.
  2. A panel that needs a coordinated, tested combination of short-circuit protection, switching, and overload.
  3. A single-phase 220V VFD driving a three-phase motor.
  4. High-cycle duty — plugging, inching, frequent jogging or reversing.

If your job does not fit cleanly into any one of these, it is probably a mix of 1 and 4, which is the most expensive mix to get wrong.

Situation 1: One motor, DOL, protection already upstream

This is the majority of orders, and the simplest answer applies: you do not need a motor starter as a product. You need a contactor, a correctly sized thermal overload relay, and whatever auxiliary contacts your control circuit actually uses.

Take the LC1D18 — the model that comes up most often in my inbox. Per Schneider's TeSys D catalogue data, at AC-3 duty (squirrel-cage motors, started and stopped while running) it is rated 18A at 400V and handles 7.5kW at that voltage. The LC1D09 is 9A / 4kW, the LC1D12 is 12A / 5.5kW, the LC1D25 is 25A / 11kW. Those are AC-3 numbers. If you are sizing off the AC-1 rating because it looks bigger and therefore safer, you are sizing the wrong way. AC-1 is for resistive loads and tells you almost nothing about motor duty.

Here is the blindspot: most buyers focus on the amp rating printed on the front of the contactor and completely miss the coil voltage suffix code. That code is where the money goes.

  • M7 = 220V AC 50/60Hz (the default in most of Asia and Europe)
  • F7 = 110V AC
  • B7 = 24V AC
  • BD = 24V DC
  • Q7 = 380/400V AC

In my first year doing this (2017), I ordered 42 LC1D18s with the wrong suffix. Everything about the order looked fine — correct frame, correct amps, correct quantity. The panels came in with a 24V DC control bus and we had ordered AC coils. That was $1,680 of stock we could not use, a three-day line stoppage, and a very uncomfortable call with a project manager. The lesson was not about checking the coil. The lesson was that the coil voltage goes on the purchase order as its own spelled-out line item, not as a suffix attached to a part number that someone can pattern-match wrong.

Two more things I would put on any DOL order. First, the overload relay has to cover the motor's full-load amps, not the contactor's rating — an LC1D18 paired with an LRD21 (12–18A) is a common pair, but a motor pulling 19A needs the LRD22 (16–24A) even though the contactor itself is fine. Second, ambient temperature. A contactor inside a sealed enclosure at 50°C+ is going to derate, and I generally go up one frame when I know the ambient is above 40°C and the duty is anything more than occasional.

Add a surge suppression module (LAD4RCU or the RC equivalent) whenever a PLC output drives the coil. Without it you will eventually replace an output card, and you will spend a day finding out the contactor caused it.

Situation 2: You actually need a motor starter

Here is where I disagree with how most people buy. The assumption is that a motor starter is the safe, professional choice and contactor-plus-overload is the cheap shortcut. In reality, for one small motor with protection already handled upstream, a starter is often over-specified — and if the combination has never been tested together, it is not automatically safer either.

What a starter actually buys you is a tested combination: short-circuit protection, isolation, switching, and overload in one assembly, coordinated so a short circuit does not weld the contactor contacts. That coordination is defined in IEC 60947-4-1 as Type 1 and Type 2 — Type 2 means no damage to the contactor or overload beyond normal contact wear, which is what most specification writers are really asking for. You do not get Type 2 coordination by buying three parts that each look fine in isolation. You get it by using a combination the manufacturer has published as tested.

So my rule is simple: if the specification calls for a coordinated combination, buy the published combination. Schneider publishes these as the TeSys GV2 motor circuit breaker plus LC1D contactor plus LRD overload, or as the TeSys U starter-controller for the compact version. Do not assemble it from whatever is on the shelf and assume the coordination carries over. It does not.

Where people get burned is the middle ground — buying something that looks like a starter (breaker, contactor, overload in one housing) from a source with no published coordination table. It is cheaper, it looks identical on a drawing, and nobody finds out it was wrong until a short circuit takes out the whole line. I have watched that happen twice. Both times the saving on the panel was under $200.

Situation 3: Single-phase 220V VFD driving a three-phase motor

This is not really a selection question. It is a wiring question, and it is where I did the most expensive damage.

The rule is short: never put a contactor between a VFD output and the motor while the drive is running. Opening that circuit under load turns the motor's inductance into a voltage spike that goes straight into the drive's output stage. In 2019 I let a panel builder wire a contactor on the output side of two 0.75kW drives, on the theory that the contactor would double as the emergency stop. It did. It stopped the drives permanently. Two units, about $900, plus a week of lost production.

If you need switching alongside a VFD, the options are: use the drive's own start/stop terminals (the normal answer), put the contactor on the input side purely as a disconnect (but do not use it for frequent cycling — the pre-charge circuit will not enjoy that), or use it as a bypass contactor in an arrangement where the drive and contactor are interlocked and the drive is stopped before the contactor changes state.

The other single-phase 220V VFD mistake is the motor winding. A single-phase 220V input drive puts out three-phase 220V, not 380V. A motor nameplated 380V/220V star/delta has to be connected in delta at 220V. Connected in star it will run, badly, with low torque, and eventually not at all. I once watched a technician lose half a day to that while the drive reported no fault whatsoever.

Situation 4: High-cycle duty

If the motor is jogged, inched, plugged, or reversed frequently, you are in AC-4 territory, and the AC-3 rating is not the number you should be reading. AC-4 duty eats contact material. The practical fix is to oversize one frame — an LC1D25 doing the work of an LC1D18 — or to use a drive and stop switching the motor at all. In my experience the oversizing costs a few dollars per unit and buys years of service life, which is a trade I will make every single time.

The accessories people forget until the panel is built

Contactor accessories are the easiest line item to drop off a purchase order and the hardest to source at 4pm on a Friday. Auxiliary contact blocks (LADN11 for 1NO+1NC, LADN22 for 2NO+2NC) should be counted against the control drawing rather than guessed. Reversing pairs need the mechanical interlock kit and two contactors with the same coil code — I have mismatched that once, and the interlock will not save you from a wrong coil. Terminal shrouds and marker plates are cheap and always the thing that holds up the panel build. If ordering from a distributor that stocks the full TeSys range, it is worth pulling the accessory list at the same time as the contactors, because availability on small parts is what usually slips.

How to tell which situation you are in

Four questions, in order:

  1. Is there a VFD? If yes, you are in Situation 3. Contactor goes on the input or in bypass, never on the output.
  2. Does the specification require a coordinated combination, or does the panel need isolation and short-circuit protection in one device? If yes, Situation 2 — buy the published combination.
  3. Does the motor start more than a few times an hour, or jog or reverse? If yes, Situation 4 — oversize one frame.
  4. None of the above? Situation 1. Contactor, correctly matched overload, correct coil code, done.

If a job spans two of these — a high-cycle motor with no VFD, for example — follow the more conservative of the two answers. That is not a compromise; it is just how the failure modes stack.

The checklist I actually use

I would rather spend ten minutes on a checklist than a week on a reorder. An informed buyer asks better questions and gets a faster answer, and that is genuinely better for both sides of the transaction.

  • Coil voltage written out as its own line on the PO, not just as a suffix.
  • Utilization category stated (AC-3, or AC-4 if it applies).
  • Overload relay range covering the motor's FLA, with the actual nameplate amps attached to the order.
  • Auxiliary contacts counted against the control drawing.
  • Ambient temperature inside the enclosure, with derating applied above 40°C.
  • Surge suppression on any coil driven by a PLC output.
  • Nothing between the drive output and the motor.

And verify current part numbers and list pricing against the current Schneider TeSys catalogue before releasing the order. Catalogue data gets revised, and a part number you memorized in 2021 is not a part number you should trust in 2025. If you ask me, those ten minutes are the cheapest insurance in the whole panel.

Kwame Boateng

Kwame Boateng

Kwame Boateng is a transformer and power-conversion analyst specializing in distribution transformers, power supplies, inverters, and network integration. He uses IEC 60076 test data for transformer ratio, impedance, losses, and temperature rise, and IEC 62477-1 safety requirements for converter insulation and thermal boundaries while separately comparing harmonics and efficiency curves. He helps engineers and sourcing teams compare equipment against duty profiles, environmental limits, short-circuit behavior, lifecycle energy cost, and service requirements.